Feltona Epoxy Primer DT 6.7 kg (A+B)

3 625 kr
Inkl. mva. Frakt til hentested vanligvis 200-350 kr. Gratis henting i Oslo.

På lager

Feltona Epoxy Primer DT is a primer for floors where you are unsure about the moisture content of the substrate, for example a tiled floor. We recommend it for bathroom floors and self-levelling compounds.   Epoxy Primer DT is a two-component, solvent-free primer. Epoxy Primer DT is intended for use on mineral substrates such as concrete, masonry, plaster and tiles. Apply to untreated substrates before further treatment with epoxy, polyurethane or microcement. Epoxy Primer DT is particularly suitable for concrete with moisture on the surface. Must be sand broadcast.   Application data:   Colour: Clear, yellowish Application method: Squeegee, rubber squeegee or notched trowel. A roller can also be used Cleaning agent: Xylene or Isopropanol. Cured product can only be removed mechanically. Thinning: The product must not be thinned. Recommended consumption: Approx. 0.2-0.4 kg/m2, depending on the substrate Pot life: 50 min. Should be used immediately after parts A and B have been mixed Dust dry: 2 hours (20°C, 505 R.H) Maximum overcoating time: 48 hours (20°C, 505 R.H) Application temperature: From +12°C to +30°C for both substrate and air, and at least 3 C above the current dew point. Curing time: 5-7 days Shelf life: 2 years in unopened packaging at normal storage temperature   Instructions for use     Pre-treatment The substrate must be firm, clean, dry and free of grease. Maximum residual moisture in the substrate 5% (95 RH). Concrete grade min. C 25. Concrete must be pre-treated by grinding, milling, shot blasting or sandblasting. Vacuum the surface thoroughly at the end.   Mixing and application Pour part B into part A and mix thoroughly for 3-4 min. using a slow-speed drill with a mixer attachment. The mixture must be used immediately. Apply evenly and generously with a squeegee, rubber squeegee or notched trowel. The minimum application temperature is +12°C; this applies to both the substrate and air temperature. The product temperature must be above +15°C when used. After application, all pores must be filled and the surface must appear sealed, with no dry patches. This is important to prevent air bubbles in the topcoat. The topcoat must be applied within 48 hours. If this time interval is exceeded, the surface must be lightly sanded to ensure adequate adhesion. The primer can be sand broadcast to increase adhesion between the products.
Les hele beskrivelsen
Betal enkelt og trygt med Vipps i kassen
  • Levering i post2-7 dager
  • Hent i OsloMandag-fredag i åpningstiden
  • ReturvilkårSe vilkårene som gjelder for denne varen
  • Usikker på mengde?Regn ut i Pakkevelgeren
  • Spørsmål om produktet?Chat med oss - svar med en gang, døgnåpent
Se leverings- og returvilkår

Leggeanvisning

Slik legges Feltona Cretezenz, gulv og vegg på én side

Primer, base, medium og lakk i fire trinn, med tørketider og slipekorn for hvert lag. Pluss det du må gjøre før du starter, og hvor lenge badet må stå før du dusjer.

Trenger du hjelp til å velge, eller regne ut mengde? Få pristilbud →
Beskrivelse

Feltona Epoxy Primer DT is a primer for floors where you are unsure about the moisture content of the substrate, for example a tiled floor. We recommend it for bathroom floors and self-levelling compounds.

 

Epoxy Primer DT is a two-component, solvent-free primer. Epoxy Primer DT is intended for use on mineral substrates such as concrete, masonry, plaster and tiles. Apply to untreated substrates before further treatment with epoxy, polyurethane or microcement. Epoxy Primer DT is particularly suitable for concrete with moisture on the surface. Must be sand broadcast.

 

Application data:

 

Colour: Clear, yellowish

Application method: Squeegee, rubber squeegee or notched trowel. A roller can also be used

Cleaning agent: Xylene or Isopropanol. Cured product can only be removed mechanically.

Thinning: The product must not be thinned.

Recommended consumption: Approx. 0.2–0.4 kg/m2, depending on the substrate

Pot life: 50 min. Should be used immediately after parts A and B have been mixed

Dust dry: 2 hours (20°C, 505 R.H)

Maximum overcoating time: 48 hours (20°C, 505 R.H)

Application temperature: From +12°C to +30°C for both substrate and air, and at least 3 C above the current dew point.

Curing time: 5–7 days

Shelf life: 2 years in unopened packaging at normal storage temperature

 

Instructions for use

 

 

Pre-treatment

The substrate must be firm, clean, dry and free of grease. Maximum residual moisture in the substrate 5% (95 RH). Concrete grade min. C 25. Concrete must be pre-treated by grinding, milling, shot blasting or sandblasting. Vacuum the surface thoroughly at the end.

 

Mixing and application

Pour part B into part A and mix thoroughly for 3–4 min. using a slow-speed drill with a mixer attachment. The mixture must be used immediately. Apply evenly and generously with a squeegee, rubber squeegee or notched trowel. The minimum application temperature is +12°C; this applies to both the substrate and air temperature. The product temperature must be above +15°C when used. After application, all pores must be filled and the surface must appear sealed, with no dry patches. This is important to prevent air bubbles in the topcoat. The topcoat must be applied within 48 hours. If this time interval is exceeded, the surface must be lightly sanded to ensure adequate adhesion. The primer can be sand broadcast to increase adhesion between the products.

Bruksområde
Egnet bruksområde avhenger av underlag, rom og ønsket finish. Kontakt oss ved tvil.
Frakt og levering
Levering i post: 2-7 dager. Hent i Oslo: mandag-fredag i åpningstiden. Fraktpris beregnes i kassen.
Usikker på hva du trenger? Vi hjelper deg med riktig produkt og mengde.

Flere produkter

Se alle →